Drive Items
Mamod engines Drive Items
Everything that revolves, spins or turns is an associated component of Drive Items.
MAMOD SA1 ROADSTER BACK AXLE
ALSO FOR LIMO / VAN / BUS
Length = 162mm
STEAM ROADSTER PLASTIC AXLE GUIDES
SIX IN THE SET - AXLE NOT INCLUDED.
For your Mamod Roadster etc. upgrade.
STEAM ROADSTER REAR AXLE BRASS SPACER
For your Mamod Roadster etc. upgrade.
The Rear Axle requires a spacer on one side to bring the wheel out to match the width of the front wheels.
These can be used instead of the more usual chrome hub caps.
ROADSTER ETC. SA1
This pulley fits onto the back axle and is joined by drive band (driving) to the brass pulley close to the flywheel (get it?).
The diameter is 58mm.
These can be used instead of the more usual chrome hub caps.
This is the pulley that fits the current style SA1, WHERE BOTH DRIVE BANDS ARE ON THE SAME SIDE OF THE VEHICLE.
There is a short drive band that connects this Pulley to the Flywheel and a longer one that connects the Flywhel to the driving road wheel.
This 32mm diameter pulley has no screw fixing but is an interference fit onto the shaft. If it is not a tight fit you can use a drop of Loctite or super glue.
TRACTION ENGINE TE1A/ STEAM ROLLER SR1A/
You know what a car looks like without hub caps - same with your mobile engine.
These Hub Caps fit the larger diameter axle such as the rear wheels of the Traction Engine and the Steam Roller.
TRACTION ENGINE TE1A/ STEAM ROLLER SR1A/ ROADSTER ETC.SA1
These Hub Caps fit the smaller diameter axle such as the front wheels of the Traction Engine and the Steam Roller.
Also the other vehicles such as the Roadster SA1.
FOR YOUR TRACTION ENGINE / STEAM WAGON STEERING FORKS.
ROADSTER ETC. SA1
This is made for the SA1 type vehicles such as the Steam Roadster.
DIMENSIONS: OD 1.89 INS/ ID 0.185 INS
ROADSTER ETC. SA1
This is made for the SA1 type vehicles such as the Steam Roadster.
BLACK INTRODUCED 2020.
DIMENSIONS: OD 1.89 INS/ ID 0.185 INS
MECCANO / SP3 ENGINE / WS1 workshop line shaft pulley.
This is the best we can do to provide you with a new flywheel .........
Read on....................
This flywheel is supplied for the Mamod MM1/ SP1 Engine
Superglue to the shaft.
There is a suitable pulley groove to drive small accessories.
TRACTION ENGINE TE1/TE1A -STEAM ROLLER SR1A
This is the Standard Flywheel sold by Mamod today for all of their engines (except SW1/SP4/SP5/SE3).
DIMENSIONS: OD 53.50mm/ ID 4.70mm
SP4 / SP5 and the old SE3 engine.
Now supplied by Mamod fully painted around the rim.
A brass screw attaches this to the crankshaft.
The dimensions are: Dia. 63.80mm, Crank shaft hole 4.73mm and width 12.34mm.
TRACTION ENGINE TE1A/ STEAM ROLLER SR1A/ STEAM WAGON SW1/ ROADSTER ETC. SA1
'Now didn't I tell you to go easy on the lever? Look at it..... you've ruined it.......all bent like that. Don't you go asking me to buy you another one!''
Note: You can buy a new one so cheap she'll never find out!
FOR YOUR TRACTION ENGINE / STEAM ROLLER / STEAMWAGON STEERING FORKS.
MAMOD FRONT WHEELS (X 2)
(NOW WITH TYRES)
TE1/ TE1A/ TRACTION ENGINE
SW1/ STEAM WAGON
This one has NO fixing screw but if you need one with the fixing screw, please go to:
https://www.modelenthusiasts.com/MAMOD-ROAD-WHEEL-(ONE-)-SA1-ROADSTER-WITH-AXLE-FIXNG-SCREW.html
Price is for one wheel.
This one has a fixing screw to tighten it to the rear axle.
If you want the no-fixing type please go here:
https://www.modelenthusiasts.com/MAMOD-ROADSTER-RED-ROAD-WHEEL.html
Price is for one wheel.
Don't do to these what you did to the last pair - whatever that was!
I know you're going to buy them, you know you're going to buy them, but the wife doesn't, so hurry up before she finds out what you're thinking. Quick, I can hear her furry slippers approaching - doh!
This steering wheel with column is fitted to the SA1 range of vehicles. It is all very well made and will last in good condition for many many years. This type was introduced early 2020.
This "Balance Wheel" sits just below the red Flywheel.
It has its own axle and two Hub Caps which are included in the price.
Picture shows the whole drive train but price is for "as described above".
This is the standard Mamod produced Steam Wagon Flywheel in red.
I
TRACTION ENGINE or STEAM WAGON
This should last you for 50+ years (probably more) unless you tread on it..............
and then you will need to buy a new one!
Apart from that you won't need to buy another one for that engine.
Important Note:
These new type (2020) Forks are incompatible with Steering Rods made pre-2020 - thread is different.
Your options are:
1. Buy a new Steering Rod
2. Buy an adapter.
3. Don't use a Steering Rod
>>>If you need any help or guidance please call Trevor
on 0777 552 1452.
How did you bust the other one? A bit heavy handed eh?
Don't lose confidence in your self just because you knackered the other one when you dropped the engine through the loft hatch and it fell eight feet onto the upstairs landing causing the wife to yell up the stairs.... "What the hell are you up to now". A familiar refrain eh?
Anyway back to business... do you remember where you put your credit cards? Oh, by the way, some people call them forks (fork).... whatever.
Just occassionally we hear of a right old knackered car that wanders all over the place with one wheel going one way and the other off in another direction. Well, maybe yours needs an overhaul in the nether regions?
For your Steering Rack that has lost its King Pin.
MAMOD
TRACTION ENGINE/
STEAM ROLLER/
STEAM WAGON
OLD STYLE STEERING ROD END FITTING
NOT MADE BY MAMOD & RARELY AVAILABLE, BUY ONE!
Brass fitting and locking nut to fit the end of the Mamod steering rod.
Note: This is not compatible with the new type (2020+ steering rods and forks).
MAMOD STEERING ROD/
TRACTION ENGINE / STEAM ROLLER / STEAM WAGON
TIP TO TIP = 10 INCHES
STEER YOUR MAMOD WITHOUT BUSTING YOUR BACK - BUY A ROD!
When you buy a trailer for your Mamod mobile engine, you may find the kind seller forgot to mention there is no tow bar - BLAST!
But being a resourceful kinda person you have been searching for one........ and that could be how you got here. Well, thank the Lord, we are trying to shift our stock! So, this is where need meets availability.
Fill your boots with as many as you like.... please!
Just the Tow Bar is for sale and not the wheeels etc!
For your Mamod engine improving project!
Made by Mamod Ltd in their Birmingham factory
The driving wheel tyre is grooved to take the TE1A drive band.
The METAL WHEELS and RUBBER TYRES are part of this offering!